How to Grow Hydroponic Cannabis at Home Hydroponics is when you grow your cannabis plant in an inert medium like coco or a reservoir of water, and provide all the nutrients to the plant directly Learn how to best use hydroponic growing systems and techniques to cultivate cannabis and how these techniques can improve your crop. The Flora Series from General Hydroponics is your tried & true nutrient solution for hydroponic cannabis growing, trusted since the 1970s
How to Grow Hydroponic Cannabis at Home
Hydroponics is when you grow your cannabis plant in an inert medium like coco or a reservoir of water, and provide all the nutrients to the plant directly in the water.
Growing in coco coir can be considered a type of hydroponics since it naturally contains no nutrients and you must provide all the nutrients in the water. However, when you say “hydroponics” most people think of this:
When it comes to hydroponic cannabis…
Differences Between Soil & Hydro
- The optimum pH for coco and hydroponics is 5.5-6.5, while the optimum pH for soil is 6-7
- Nutrients must be provided from when a hydroponic plant is a seedling (in seedling doses to start), otherwise the seedling will grow slower because it only has what’s contained in the seed itself. In soil you don’t need to add nutrients for a few weeks since there’s already some in the soil
- Growing in coco coir (a growing medium that looks somewhat like soil but is actually made of dried coconut husks) gives you results that are somewhat between growing in soil and growing in a hydroponic reservoir of water – you get a lot of the benefits of both
Pros of Hydro
- Plants in hydroponic setups generally grow faster in the vegetative stage than soil-grown plants
- Less likely to get bugs
- Buds can feel more potent
- If growing in a reservoir you don’t have to worry about watering your plants when they’re dry, over/under watering, or removing runoff. Everyone is different but I find maintaining a hydro reservoir easier than moving the plants around or watering and using a wet vacuum to remove runoff (but we all have our personal preferences!)
- If growing in a reservoir you use a very efficient amount of nutrients since you only mix up new water a few times a month, and only toss old water after the plant has already used up a lot of nutrients, which can save quite a bit if you’re using expensive nutrients and is better for the environment (compared to drain-to-waste)
- You have more control over nutrient levels, PPM, and pH – for the mad scientists among us who want to get the most out of our plants as possible!
Cons of Hydro
- Hydro usually takes more preparation/setup than growing in soil. You’re providing more for the plant instead of letting the soil do some of the work for you
- It can be easy to get root rot in hydro if you don’t provide your plant with a good-bacteria supplement like Hydroguard.
- Soil-grown buds may have a more complex or stronger smell than hydro-grown buds, especially if grown in composted living soil without any liquid nutrients
- Growing in soil is more intuitive for many people, and some people already have experience with soil from other types of gardening!
Is Hydroponics Good for Growing Cannabis?
Have you seen cannabis plants growing with their roots just floating in a reservoir of water? This type of hydroponics is known as Deep Water Culture (DWC), and has been around for over a 100 years! As more growers gain experience with this medium, DWC has become increasingly popular for growing cannabis. Hydroponic setups are really neat and offer some big benefits over growing in soil!
Benefits of Hydro Over Soil
- Plants grown in a hydroponic reservoir tend to grow faster in the vegetative stage, resulting in bigger yields and faster harvests
- Hydroponic buds tend to be more potent and often cost more at dispensaries
- Once a hydroponic reservoir is set up, it does not take a lot of work or time to maintain. Instead of regularly watering plants and removing runoff, a hydro reservoir only requires you dip a PH Pen and top off with more water or adjust as needed.
Cons of Hydro
- Takes more time and effort to set up than soil or coco
- Buds grown in soil without added nutrients tend to have a stronger smell than buds grown with liquid nutrients like in a hydroponic setup (though if you’re trying to keep things low odor this might be a benefit).
- Unless you protect your roots by using the right supplements and equipment, your plants may struggle with root rot. Luckily if you follow the steps in this tutorial you don’t need to worry about root rot killing your plants!
Hydro is a no-brainer for me. Whenever I go back to a hand-watered grow like coco coir, I am always surprised by how much extra time it takes to water plants and remove the runoff. The most intimidating part of hydro is just getting started – after that it’s actually really easy to take care of your plants. In my opinion, hydro is far easier and less time consuming than growing in soil or coco coir once you’re set up. If you are interested in hydro, go for it! If you follow this tutorial you will succeed!
Today I’ll teach you how to set up your hydroponic reservoir for growing cannabis, and I’ll show you what you need to do each day for optimum growth
How to Grow Cannabis in DWC
So there are five major parts to getting set up. You need….
- Grow Environment – I personally recommend a grow tent as opposed to building your own environment from scratch.
- Grow Light – If you don’t already have a grow light, I recommend getting a 250W, 400W or 600W HPS grow light for your first grow. They are the most consistent type of grow light and get really great results in DWC.
- Nutrients – I highly recommend getting GH Flora trio, Calimagic (Cal-Mag supplement) and Hydroguard.
- Seeds – Learn where to get seeds
- DWC tank – Learn how to build your own (it’s surprisingly hard to find a pre-made tank considering how cheap all the parts are!)
Once you’ve got your gear and supplies, it’s time to get set up and start growing! Here’s a quick overview.
How to Grow Hydroponic Cannabis
I n the previous post, we gave an overview of hydroponic gardening including its origins, the various systems and techniques, and medium options for a hydroponic grow. In this next article, we will focus how to use hydroponic systems specifically for growing cannabis.
What Is Hydroponic Cannabis?
The common nickname for cannabis—“weed” —comes from its ability to grow almost anywhere, under varying conditions and different climates. “Hydroponic cannabis” simply refers to plants grown using a nutrient-water solution and an inert growing medium rather than nutrient-rich soil. This method could be something as basic as hand-watering pots of inert medium with a nutrient solution. As discussed in the first part of this series, sophisticated systems with multiple pumps, timers, and reservoirs can take some of the daily labor out of growing, but they require more maintenance and setup time as well as a greater initial investment.
Cannabis growers have been using different hydroponic methods for many years as a way to maximize yields and speed up growth, the two main advantages of soilless growing. Working with soils indoors can be inefficient and difficult for a number of reasons:
- You may not be able to recycle soil
- Susceptibility to pest problems
- Difficult to determine proper amount of nutrients
- Need to carefully monitor soil pH
- Soil quality significantly influences the final product
With some hydroponic methods, you get to use small amounts of grow media that can often be reused while also precisely controlling what nutrients the plants are receiving and pH levels. With such levels of control, growers find that their buds are bigger, healthier and more potent.
Whether you have grown cannabis before or have no experience growing cannabis whatsoever, hydroponics can be a great way to produce cannabis in any size space. At first it can be confusing and slightly overwhelming, but by learning the basics you will come to understand it’s not as difficult as you imagined.
Set Up Your Hydroponic Cannabis Growing System
There are numerous setups for growing hydroponically with varying benefits that were discussed previously here. And while there are several types of hydroponic setups that don’t use any type of growing medium at all, many of them still use some sort of substrate to support root growth.
Various materials all provide slightly different benefits and drawbacks, so some thought should be put into choosing the right medium for your cannabis plants. In this article, we are going to be utilizing the drip line hydroponics technique.
While this system is built from the ground up, it should be noted that there are plenty of plug and play systems available for those looking for something that is easy to set up. Plug and play systems come with everything you need in a streamlined package to allow growers to get started on the right foot.
First we will start with the supplies needed. Keep in mind this is just an example, and depending on your space and desired results, many things can be tweaked in a hydroponic system to make it most beneficial to you. This list specifically outlines equipment needed to install your hydroponic system and does not include lights, fans, filters, and other basic needs for any grow room.
Hydroponic Cannabis Supplies:
- 3 or 5 gallon bucket (one for each plant)
- Grow table
- Clay pellets (enough to fill each bucket)
- Rockwool cubes (one 1.5-inch starter plug per plant)
- Reservoir tank (depending on the size of garden)
- Water pump (the bigger the better)
- Air pump
- Air stone
- Plastic tubing
- Drip line
- Drip line emitters (one or two per plant)
Browse Hydroponic Growing Supplies
Once you have gathered your materials you can begin to construct your hydroponic setup.
- First, set up your reservoir. Your reservoir is where your nutrient solution is held. A reservoir can come in all shapes and sizes depending on your grow space and size, and it holds the water pump and the air stone. It will have a line in from the air pump to the air stone and a drainage line in from the grow table. The reservoir will have a line out from the water pump to the drip line and the power cord for the water pump.
- Next you will create your grow table. The purpose of the table is to contain and return the excess water from the plants to the reservoir. To do this successfully, the table needs to have a low point where all the excess water will travel to. This low point is where you install the drain that will take the water back to the reservoir via plastic tubing.
- You can then add your 5 gallon buckets filled with clay pellets on the table. Before using clay pellets, you should soak the pellets overnight to allow them to become fully saturated with water for your plants to drink. Also, the buckets need to have holes drilled in the bottom to allow them to drain excess water onto the grow table. It is important that the holes are about half the diameter of the clay pellets to prevent the pellets from passing through or clogging the holes.
- Take the plastic tubing coming off of the water pump and run the line to the grow table. From here you can use drip line equipment to puncture holes in the plastic tubing and extend drip line to each bucket. Finally, attach drip line emitters to the end of the drip lines.
- From here you can run your system without plants to see if everything is functioning properly. The system should not have standing water anywhere. The air pump should always be running to keep the water in the reservoir oxygenated and moving, while the 5 gallon buckets and grow table drains any excess water back into the reservoir.
- At this point you are setup and ready to create your nutrient water solution in your reservoir. Below we will introduce information about nutrients and how to use them to grow your cannabis plants.
- Once your solution is ready, can introduce your plants. Take the starts or clones that have begun growing in rockwool and place them into the clay pellets. Insert the drip line so that moisture is reaching the rockwool and roots of your starts.
A benefit this setup offers is that it can easily be expanded as you want to grow more plants as long as your reservoir has enough capacity to provide all the plants with enough water. To expand a drip line setup, all you need to do is add additional lines to the new pots.
Nutrients for Hydroponic Cannabis
When growing hydroponically, you are responsible for providing all of the nutrients necessary for plants to survive. Nitrogen (N), Phosphorus (P), and Potassium (K) are the three essential nutrients for plant growth known as macronutrients. Additionally, there are secondary and micronutrients that will help the plant develop as well. These include Boron, Calcium, Copper, Iron, Magnesium, Sulfur, and Zinc.
Many companies sell hydroponic nutrient solutions that are specifically designed for certain stages of growth. Nitrogen-rich nutrient solutions will be used in the vegetative stage while phosphorus-rich nutrients become more necessary in the flowering phase.
Nutrients will come either pre-mixed in a solution or in powder form. While powder form might be cheaper and less bulky, it is best to stick with liquid pre-mixed nutrients if you are a small-time grower as they mix with water easily and are more forgiving.
Explore Nutrients for Your Hydroponic Cannabis
When mixing in nutrients, take a few measurements to make sure your solution is safe for the plants. First, make sure you have the right EC (electrical conductivity) reading, and secondly, ensure your pH reading is correct.
The EC reading is how growers can tell how strong their solution is, and how mineral-rich the water is. The more minerals, the higher the EC rating will be. Generally speaking, a reading between 0.8 to 2.0 is appropriate for growing cannabis. When a plant is young, it will need a lower amount of nutrients as opposed to when it is flowering and growing quite big.
Another common measurement used is ppm (parts per million) which is another way of looking at how nutrient-dense your solution is. There are two different scales for ppm used in the cannabis industry: the 500 and the 700 scale. The most efficient way to determine ppm is to take an EC reading, multiply it by either 500 or 700 depending on the scale you are using. An EC reading of 2.0 would equal either 1,000 ppm (500 scale) or 1,400 ppm (700 scale). Many readers used to measure EC or ppm will do this conversion for you.
The lower the ppm, the less nutrient-dense a solution is. As a general rule, aim for the following densities based on your plant’s age:
- Seedlings/early sprouts – 100 to 250 ppm
- Early vegetative stage – 300 to 400 ppm
- Full vegetative stage – 450 to 700 ppm
- Early blooming stage – 750 to 950 ppm
- Full mature bloom/ripening stage – 1,000 to 1,600 ppm
Note what scale the nutrients you are using are based upon before making any nutrient solutions.
Next, you’ll need to balance the pH level. Between 5.5 and 6 is ideal for cannabis to absorb the nutrients. If levels are off significantly, the plants will fail to uptake the nutrients and will suffer deficiencies.
You should continue to monitor your solution by taking readings two times a day to make sure everything is at the correct levels. Regardless, it is good practice to switch out your solutions every week or two to keep the solution as optimal as possible.
Caring for Cannabis Grown With Hydroponics vs. Soil
Raising a plant with hydroponics is different in many ways from growing in a soil garden. One thing to consider is the support the plant is receiving. Unlike a plant growing in soil, plants in hydro mediums might be vulnerable to tipping or breaking. Trellising your garden will help to prevent this from happening and will also allow you to train your plants to grow in specific directions.
Another thing to consider is pruning. With hydroponics, your plants can grow extremely fast. This means you need to be diligent about pruning. Removing all the bottom foliage and topping your plant before switching to its flowering cycle will allow your top colas (the large, topmost buds) to receive all the energy they need.
Growing hydroponically does require that you invest a good amount of time and money into developing your system prior to actually starting your garden. Additionally, you’ll want to make sure your system works effectively and your nutrients are high quality so that your plants will flourish. Once you gain a knack for hydroponics, you’ll be on your way to producing world-class cannabis that is well worth the effort.
Have you ever tried hydroponic growing techniques before, either for cannabis plants or other grows? Share your advice, tips, and questions in the comments section below!
Hydroponics: The original way to grow perfect cannabis every time
There’s a reason hydroponics is such a classic choice for cannabis: It’s easy to set up, it’s space efficient, and without the variability that comes with soil, you can fine-tune your plants’ nutrients for every part of the growth cycle. There’s almost zero guesswork involved, too, thanks to decades of growers that came before you—as long as you’re able to measure things—so it works for beginners and old hands alike.
When hydroponic herb rose to prominence in the 1970s, General Hydroponics, now part of Hawthorne Gardening Company, was right there on the ground floor. By 1976, they’d released their three-part Flora Series, the OG cannabis nutrient system that growers still swear by today.
Using General Hydroponics’ personalized assistance, clear guides, and straightforward nutrient system, first-time growers can get all the basics for starting their first crop—but once you have the basics down, it’s just as easy to personalize and adapt to every individual grow.
Whether you’re just starting out with cannabis cultivation or you’re used to growing using soil, hydroculture is the most foolproof way to get a full, healthy harvest. Here’s what you need to know.
What is hydroponics?
The simple version: Hydroponics is a way of growing plants with a blend of water and nutrients instead of soil. While humans have been growing plants without soil for eons, technology has developed in the last century. It was used to feed troops in World War II, and later, it would be used to grow lettuce in space.
Hydroponics gradually spread from scientists to gardeners and hobbyists. While a lot of them were just growing veggies, it especially caught on with cannabis growers. Cannabis is a unique plant with very specific lighting, humidity, and nutritional needs, and hydroponics gave them a level of control they’d never had before. It made it easier than ever to avoid pesticides, too, since many common pests require soil to thrive.
Getting started with a hydroponic cannabis crop
A cannabis plant has two basic stages, although they break down into smaller ones. During the grow period, the priority is developing leaves and stems, creating a sturdy, healthy plant. With that strong foundation in place, you move onto the bloom phase, creating as many sticky buds as you can. For maximum yields, both of those processes need different nutrients—for example, cannabis needs the most nitrogen at the end of the growing period—and with hydroponics, it’s incredibly easy to adjust them to the plant’s exact needs at any given time.
To get started, you can either buy a premade hydroponics system or, if you’re thrifty and handy, build your own. Make sure your plants are getting adequate light, either naturally or from grow lights, and plenty of ventilation. (If you stick with it, you’ll want to look into getting more precise environmental controls, like an air conditioner.) Check your water for the proper pH level before mixing in your nutrients.
General Hydroponics’ Flora Series is the simplest way to make sure your plants are well-fed. Your plant gets all the nutrients you need in just three different blends—FloraGro®, FloraBloom®, and FloraMicro®—mixed in different combinations depending on the plant’s growth stage.
General Hydroponics’ straightforward feedchart, built from decades of experience, gives both a simplified, four-step nutrient plan and a week-by-week breakdown, giving your crop the right balance for a productive harvest.
The team at General Hydroponics are the original experts on hydroponic cannabis—and they’ve prepared a whole knowledge library to get you started. Articles for beginners cover the basics and frequently asked questions. Next-level growing resources give you everything you need to know about your growing environment, keeping your plants healthy, and troubleshooting.
But if all that doesn’t cover it, you can always give them a call. They’ll get a hydroponics wizard on the line to make sure you’re set up for success.